Rotting wooden siding is more than just an eyesore. It will breach the defenses of your home. When clapboards or shakes fail, they let in moisture, drafts, pests and rot. When the seal is broken, the damage spreads. The wood rots. The insulation gets wet. Repairs will be expensive.
Repairing a single board is faster and more cost-effective than replacing an entire part. You can do it yourself. Here’s how to replace damaged clapboards before the problem grows.
Removing the Broken Board
Speed matters. Treat the area immediately. All you have to do is replace the damaged part. The rest of the siding will likely remain unchanged.
Start by removing the damaged board from the house. Drive wedges up underneath it. This pulls it away from the sheathinging below. Locate the nails that hold it in place. Pull them out with a claw hammer or pliers.
If the nails are stubborn, cut them. Cut them flush with the sheathing with a hacksaw. Don’t force it. There is a risk of tearing the surrounding wood.
Next, release the upper part of the board. The overlapping clapboard above is probably a nail. Drive the wedges under the top board. Remove the nails. Now the damaged piece is loose on all sides.
Cutting Out the Damage
Cut the board on both sides of the rot. Use a hacksaw or a hacksaw. Accuracy helps you avoid harming your neighbors.
If space is limited, wrap one end of the hacksaw blade with electrical tape. This protects your hands from sharp teeth. Cut all the way through. Include the entire damaged area in the cut.
Adjust the wedges if you need more room for the saw. Hold them in place to hold the board up. After cutting from both sides, the damaged part should be easy to pull down and out.
If it sticks, break it up. Use a hammer and chisel. Take it out in pieces. Work carefully. One slip can damage the good wood around you.
Installation of a new clapboard
Cut the replacement board to fit the opening. It should match the original size and shape. Test the fit before attaching.
The new plate should slide into place. Its upper edge goes under the top board. Its bottom edge rests above the board below. This interlocking pattern sheds water. It keeps the air out.
Plane the edges if they are too thick. Aim for an exact fit. A tight seam prevents future rotting.
The goal is a seamless repair imitating the original structure. If the water finds an opening, the problem will repeat itself.
This resolves the immediate breach. But properly mounting the new board is the next hurdle. You need to attach it without splitting the wood. And you need to make sure that the overlap drains the water properly. This is where real skill comes into play.
Securing the Patch
Once you have a suitable test fit, it’s time to prime. Don’t skip the edges. Paint both sides of the new board and every raw cut edge where you removed the old siding. Let it dry completely. If you rush this, the exfoliation will happen later.
Slide the clapboard into the gap. The top edge goes under the board above. The bottom edge covers the board below.
Now nail it down. Use 16d nails. Drive them through the bottom of the new board, through the siding above, and into the top edge of the substrate. This will lock it in place.
Next, seal the seams. Use acrylic latex caulk around the edges of the patch. Wait for it to cure. Then paint the new siding to match the rest of the house. A good match hides the fix.
Shakes or Shingles
Damaged shingles or clapboards are replaced in the same way clapboards are. If it’s natural, unstained cedar, you need to know the trick. Take your replacement shakes from an inconspicuous area in the house. Put the new shingles in that hidden spot. This trick eliminates a new-looking, unweathered patch from the repair area.
To remove the damaged part, wedge each one out. Drive wedges under the damaged shake and the shakes that overlap it. Pull or cut off all nails, just as you did with the clapboards. Then remove the damaged shake.
If it doesn’t come off easily, split it into several parts with a hammer and chisel. Remove the pieces.
Insert the new shake. Nail it down with 16d aluminum nails. Do not use steel nails. Steel corrodes. Corrosion stains the wood. If the shaker does not have pre-drilled nail holes, drill pilot holes for the nails to prevent the wood from splitting.
Replacing damaged shingles or clapboards will prevent your siding from quickly becoming damaged. It protects your home better from the weather. But you have to stay on top of it. A small spot of rot can eat through an entire part if you ignore it.
